IoT Router 5G | Ultra-Fast, Secure, and Resilient Connectivity

1. Locate the SIM adaptor kit.

2. Push the SIM holder button with the SIM needle.

3. Pull out the SIM holder.

4. Insert your SIM card into the SIM holder.

5. Slide the SIM holder back into the router.

6. Attach all mobile antennas to connectors labelled “Mobile”.

7. Connect the 4-pin connector to the power socket on the front of the device. Then plug the power adapter into an electric outlet.

1. Ensure the Network connection is Enabled. Go to Start — Control Panel — Network and Internet — Network and Sharing Centre. Click on the Change adapter settings in the left panel, then right-click on Network Adapter, and select Enable.

2. Check if IP and DNS are obtained automatically. Right-click on Wireless Network Adapter and select Properties. Then select Internet Protocol Version 4 and click Properties.

3. If not selected, check to obtain an IP address and obtain DNS server address automatically. Click OK.

1. To enter the gateway’s Web interface (WebUI), type http://192.168.2.1 into the URL field of your Internet browser.

2. When prompted for authentication enter the username admin and enter the password located on the device information label/engraving.

3. After logging in, you must set a new password for security reasons. You will not be able to interact with the gateway’s WebUI until the default password is changed. The new password must consist of a minimum of 8 characters. Requirements: one uppercase letter, one lowercase letter, and one digit.

4. Next, the Configuration Wizard will start to help you set up some of the gateway’s main operational parameters.

5. Finally, let’s verify the Mobile signal strength. Go to the Status — Network page and pay attention to the Signal Strength indication.

To achieve the best signal conditions and maximize cellular performance, try adjusting the antennas or changing the location of your device. You can find information on signal strength recommendations here.

Mobile module	5G Sub-6Ghz SA/NSA 2.1/3.3Gbps DL (4×4 MIMO), 900/600 Mbps UL (2×2); 4G (LTE) – LTE Cat 20 2.0Gbps DL, 200Mbps UL; 3G – 42 Mbps DL, 5.76Mbps UL
Power Connector	4-pin industrial DC power socket
Input voltage range	9 – 30 VDC, reverse polarity protection, surge protection +/-1 kV 50 μs max
Ethernet	1 x RJ45 port, 10/100/1000 Mbps
I/O’s	2 x Configurable I/O pins on 4-pin power connector
Status LEDs	3 x connection type status LEDs, 3 x connection strength LEDs, 2 x LAN status LEDs, 1 x Power LED
SIM	1 x SIM slot (Mini SIM – 2FF), 1.8 V/3 V
Antennas	4 x SMA for Mobile
Dimensions (W x H x D)	100 x 30 x 93.4 mm
Weight	241g
Mounting options	DIN rail, Flat surface
Operating temperature	-40 °C to 75 °C
Ingress Protection Rating	IP30

Front View

Back View

Power Socket Pinout

Yes, Remote Management System (RMS) is a web-based management platform that allows you to monitor and manage your estate of routers remotely. CSL includes 30 days of RMS free to assist with the installation and set up of your routers. To extend this past 30 days a code can be purchased from CSL using our M2Mconnect portal or by contacting your sales rep.

For assistance with RMS setup, we have included a guide within the router box or visit our vendor’s FAQs.

Yes, CSL can provide a token to access our vendor’s VPN platform, RMS VPN, which allows for secure access, including remote connection back into the device, from any Teltonika device back to the RMS cloud platform.

For more information on RMS VPN and for the setup guide:

Contact your sales rep or Contact Us for further support.

Additionally, these routers can be configured with the most common VPNs. Support with configuring your VPN can be found here.