CSL Connected with Orisec

ARC CONNECTION

CSL Connected allows you to connect the following control panels to your chosen ARC via Orisec Cloud Services: CP/CK/CT-20, CP/CP/CK-60, W-CP-40-K/T/E, CP-50/100/200. Communication can be made in SIA II, SIA III*, Contact ID or Fast Format, using the applicable communication device (Single path
modules – CM2-GSM, CM2-IP, CM2-Wi-Fi. Dual path modules – CM2-GSM-GSM, CM2-GSM-IP, CM2-WiFi-GSM).

*SIA III is the preferred signalling method.

PANEL PROGRAMMING

Within the Orisec engineering menus, navigate to the following sections to program the required information:

Programming Menu > Comms Modules:

GSM settings (for all variants which include GSM)

• APN Name – geminit2.m2m
• User / APN2 – geminit2.m2m (only required if using dual radio – otherwise leave blank)
• APN Password – leave blank

Note – if DHCP is being utilised, no information is required in these menus.

Ethernet settings (for all variants which include LAN)

• Address – add site IP details if required
• Port – add site IP details if required
• Mask – add site IP details if required
• Gateway – add site IP details if required

Note – if DHCP is being utilised, only the router’s SSID and password are required in these menus.

Wi-Fi settings (for all variants which include Wi-Fi)

• SSID – Enter the router’s SSID
• Password – enter Wi-Fi password
• Address – add site IP details if required
• Port – add site IP details if required
• Mask – add site IP details if required
• Gateway – add site IP details if required

SINGLE PATH SYSTEMS

Programmming Menu > ARC setup:

ARC: 1
Number – Enter ARC code from page 2
Account – enter chip/account number from ARC
Protocol – enter chosen protocol – default SIA III
Dial Seq – enter 555

DUAL PATH SYSTEMS

Programmming Menu > ARC setup:

ARC: 1
Number – Enter ARC code from page 2 followed by DP grade (ie 12345DP2)
Account – enter chip/account number from ARC
Protocol – enter chosen protocol – default SIA III
Dial Seq – enter 555

Programming Menu > System Options > Monitor H/W:

Enable both these options
– Report Single Path Fault
– ATS Path Faults

ACCESS THE APP

CSL Connected is fully compatible with all Orisec applications, Control Plus, Control Plus 2, Orisec UDL & Orisec Cloud Services.

For additional information on Orisec control panels, software packages or technical support please contact Orisec:

Email: support@orisec.co.uk
Phone: 01706 398740

Q. My ARC does not appear in the list provided?
A. It may be that your chosen ARC is not one of the many ARCs that have signed up for this solution. Please contact CSL Technical Support.

Q. What grade is the product?
A. Single path units are sold as EN50136-1:2018 SP2. Dual path units are sold as EN50136-1:2018 DP2

Q. How do I know that my signals are being sent to CSL’s Gemini Platform?
A. Once you have your system on test with the ARC, enter the programming menu, select test and diagnostics and then do test calls. Whilst in this menu push enter on any test signal and ensure that 2 ticks are shown on the panel. This indicates that the test alarm has been sent to Gemini. You should always check with the ARC that they have received signals at their end too.

Q. Am I able to send signals in a different format to the one which was ordered?
A. Yes this is possible and can be selected in the panel. Please check with your ARC before making any changes to make sure that they will accept the new format.

Q. What set up do I need to do on the Orisec Cloud Services?
A. There is no set up required on Orisec Cloud Services.

Q. Why can I not see the second APN option in the panel menus?
A. For dual path devices the following software versions are required